Maintenance and assistance of the treadmill

by

How do you use treadmill lubricant?

Weekly remove with a damp cloth the residues of dust and dirt that accumulate on the metal and plastic parts, then pass a second cloth moistened with a little silicone spray to create a protective layer .

It will avoid the opacification and rusting of the tool for a correct functioning of the belt, it is recommended to apply the product on it approximately every 20 hours of use.

Toorx – Lubricant spray for treadmills

silicone lubricant Treadmill Three packs of 400ml each

See offer on Amazon

How to apply it?

To best apply the lubricant, just follow four simple steps:

  • Lift the treadmill belt on one of the two sides. If you cannot lift it, this means that it may be too tight, consequently with the help of an expert, adjust the aforementioned tension, since excessive tension could lead to damage. Of the components.

  • Using a can of silicone spray lubricate with three abundant sprays, applying it on the table or in the lower part of the belt, finally proceed with the removal of any excess silicone deposited on the side of the belt or on the frame.

  • Finally, start the tool and walk on it for two / three minutes at a low speed to be able to efficiently spread the lubricant all over the board.

Come and discover the best Norditrack treadmills and Kettler treadmills reviewed by our experienced and passionate athletic staff.

To perform general maintenance on the treadmill:

  1. First of all, place the treadmill on the floor, in a perfectly flat spot, to avoid as much as possible that the motor and the belt of the tool can find themselves out of balance.

  2. With the help of a soft and dry cloth, we remove all traces of sweat that we find first on the handles and on the belt to avoid possible injuries.

  3. Subsequently, on all the other parts, to avoid any type of corrosion.

Weekly, it is advisable to carry out targeted maintenance, which comprises the following steps:

  • It is advisable to clean the display of the tool at least once a week with the use of a damp and clean cloth in order to avoid the accumulation of dust and dirt.

  • Perform a general cleaning of the treadmill using only a cloth soaked in water. Do not use any type of detergent, soap or solvent as they may damage the latter.

  • Using a vacuum cleaner, remove the dirt and dust accumulated over time under and around the tool to prevent the latter from coming into contact with the tape or other sensitive parts in the long run.

  • With a damp and soft cloth, clean the entire area of the platform, in particular the section between the frame and the belt that is lifted, in order to avoid problems related to its movement.

  • Finally clean the entire tape by rotating it 180 degrees by repeating the step twice using a vacuum cleaner and then a dry cloth.

After performing the weekly maintenance, it is necessary to carry out the monthly ones, the most important to ensure the correct long-term functioning of your treadmill.

Before performing any type of action, make sure that the treadmill is turned off and disconnected from the power supply in order to avoid accidents.

  • First, unscrew the screws and lift the motor casing in order to subsequently vacuum the treadmill motor. In particular, clean the area in which the fan is located and the one below it with greater precision. Thoroughly and accurately clean all dirt and dust accumulated inside. Do not use water for cleaning and avoid touching any electrical component directly as much as possible.

  • A fundamental part is the inspection of the drive belt, making sure that there is no excessive wear and that it is correctly aligned for use. Once finished, replace the engine casing without screwing it.

  • Now move on to cleaning the running board with the use of a damp cloth that needs to be passed between the latter and the treadmill belt. In case of stubborn dirt, it is advisable to use denatured alcohol.

  • After these steps, it is necessary to re-lubricate the treadmill table using only and exclusively the silicone spray, as other preparations could damage the components of the tool.

  • Start the treadmill at a low speed, step on the belt holding firmly to the handrails and try to block the belt by placing your feet on it, if the belt stops but the motor continues to spin it means that something inside is slipping, check consequently components such as the belt or pulley as they could be the cause.

  • Refit the engine casing, fixing it with a couple of screws, then connect the treadmill to the electrical outlet and test the tool for 15-20 minutes in the mode you use most. At the end, disconnect the treadmill from the electric current, uncover the motor casing and measure the temperature of the metal casing (be careful as some components will still be live), it must not exceed 45 °, if it exceeds it, contact the technical service of the product or a skilled technician a situation could lead to future breakdowns, otherwise you can purchase a “low friction” belt which solves 90% of treadmill problems.

  • Finally, check that the load-bearing components of the treadmill structure such as the mounting screws are not loosened, if necessary tighten them, also tighten all the screws of the motor casing but not those of the treadmill wheels, as they must have a certain “play” to move freely.

Properly lubricate the treadmill.

To ensure a maximum and efficient life of your tool, it is necessary to pay close attention to the correct lubrication.

There are many types of different products for this purpose, such as lubricating oil, silicone oil and the most commonly used sprays.

However, the most recommended is silicone oil , because besides increasing the life of the motor and the treadmill board by reducing the friction that forms between the table and the sliding canvas, it also allows you to prevent or reduce any annoying noises. Coming from the mechanical parts of the tool.

Leave a Comment